Engineering
OGRD Middle East has a full complement of design engineers that collaborate with the client to ensure our engineering services are tailored to the client requirements. We focus on innovative and cost-effective engineering solutions that serve the overall project execution, allowing us to optimize construction and fabrication cost.
In additional to greenfield projects, we can troubleshoot, debottleneck and provide brownfield solutions to optimize or modify existing facilities. Our engineering services cover all stages including pre-FEED, FEED, Detail Engineering, Construction Support, Commissioning and training of operations. GRD Middle East has unrivalled depth in integrating construction and fabrication into our engineering solutions.
Process Engineering
- Aspen HYSYS V9 Gas Processing
- Aspen HYSYS Acid Gas Cleaning
- Aspen HYSYS Upstream
- Aspen Flare System Analyzer
- Aspen HYSYS Relief Sizing
- Aspen HYSYS Blowdown Technology
- Aspen HYSYS Dynamic Modelling
- Aspen Exchanger Design & Rating
- Aspen HYSY Hydraulics
- Aspen Equipment Sizing
Typical Process
Engineering Deliverables
- Process Modelling
- Energy & Utility Optimization
- Dynamic and Safety Analysis in Accordance w/ API Quality and Safety Standards
- Equipment Sizing
- Hydraulic Modelling and Transient Analysis
- Block Flow Diagram
- Process Flow Diagram
- Heath and Material Balance
- Piping and Instrumentation Diagrams
- Process Narrative
- Utility Flowsheets
- Line Designation Table
- Alarms and Set Point list
- PSV list
- Car Seal list
- Tie-in list
Mechanical Engineering Deliverables
Our mechanical engineers are trained in ASME, CSA, API, TEMA, ASTM, NACE design principles and codes.
- 3D Design
- Smart P&ID
- Vessel Design
- Pipe Stress Analysis
- Pump & Compressor selection and optimization
- Waterflood applications
- HVAC Design
- Mechanical Specification development
- Material Selection
- HAZOP
Civil, Structural &
Geotechnical Engineering
- Civil, Structural and Geotechnical Engineering and Design
- Industrial Site Planning and Development
- Power Generation and Electrical Equipment Support Structures
- Steel, Concrete Engineering and Design
- Condition Assessment of Existing Industrial Facilities
- Site Grading, Site Drainage and ContainmentRoad Engineering and Design
- 3D Modelling
- Building Structure and Foundation Engineering and Design
- Pipe and Cable Tray Racks, Bridges and Miscellaneous Supports
- Modular Structures and Skids
- Storage Tanks and Silos Structural Bases and Foundations
- Industrial Equipment Structural Frame and Foundation Support
- Deep and Shallow Foundation Engineering
- Softwares (S-Frame Software, RISA-3D, RISA-Connection, SAP2000, Ensoft L-Pile, Dyna 6.1
Electrical Engineering
- Specification and Design of Complete Electric Systems
- Electrical Generating Plants – Steam, Diesel, Natural Gas Turbine and Reciprocating Sets
- Substations and Distribution – Power Generation, Distribution, Transmission
- Solar and Renewable Power Electrical Systems
- Protective Relay – Selection, Application and Coordination
- Load Flow and Short Circuit Studies Analysis, Arc Flash Hazard Analysis
- Motor Control and Application
- Grounding and Lighting Protection
- Hazardous Area Classification and Design, Fugitive Emissions Studies
- Lighting Systems
- Communication and Data Acquisition Systems – Fiber and Copper
- Fire Detection and Alarm Systems
- Electric Heat Tracing Systems, Mineral Insulated and Self-Regulated
- 3D Modelling
Instrumentation
- Specification and Design of Instrumentation
- Facility Inlet Over Pressure Protection Requirements
- Pressure Safety Valve Sizing Requirements
- Pressure-relieving and Depressurization Systems
- Burner Management Systems
- Oil and Gas Safety Shutoff Valve Requirements
- Generator Fuel Trains
- Instrumentation Secondary Sealing Requirement
- Control Valve Sizing and Selection
- Flow Meter Sizing
- Thermowell Wake Frequency Calculation Software
- PSV Sizing
- Facility Metering Design
Controls
- Safety Requirements Specification Development (IEC-61511 Safety Standards)
- LOPA / HAZOP Reviews
- SIS Design and Implementation (IEC-61508)
- Shutdown Key and Cause & Effect Development
- Logic description and control narrative development
- Control strategy development and implementation
- Design, Integration, Implementation, testing and commissioning of field RTU/PLC/DCS and associated measurement and control devices
- Factory Acceptance Testing (FAT)
- HMI System design and programming
- Construction, Commissioning and startup support
